Powertrain Control for 2005 Chevrolet SSR
Vent Valve
2005-09. 2002-04. 4.3l. Location-Vapor Canister. 4.2L. 5.3L. All models. 6.0l. SSR. Controls fresh air flow to the canister Sends fuel vapors to the engine for re-burn Helps control fuel tank pressure
Purge Valve
Controls vapor flow from canister to engine
M.A.P Sensor Seal
1/2 ton. Canister & sensors. 3/4 ton. 5.3L. 2008-09. 2.4L. This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors
Ft Oxygen Sensor
Front. 5.3L. SSR. Detects oxygen content in the exhaust gases to help optimize emissions This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors
Rear Oxygen Sensor
This part requires programming and/or special setup procedures GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle Detects oxygen content in the exhaust gases to help optimize emissions This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors
All models. 4.2l. 129 wheelbase. Relay. Terraza. All models. 5.3l. 129 wheelbase. Uplander. 121 wheelbase. Montana SV6. SSR. Helps reduce harmful pollutants from entering the atmosphere Captures fuel vapors to be re-burned in the engine This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors
High quality coated windings to improve durability and provide protection against internal shorts and dielectric breakdown Silicone steel plates surrounding the ignition coil correctly match the original part size and number exactly Laminations are coated to hinder corrosion and many feature molded plastic protection to help ensure that nothing is exposed
Ignition Coil Bracket
2003-05, 5.3L. 6.2L without supercharger. 6.0 & 6.2L. 7.0L. 2008-09. This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors
Plug Wire
4.8, 5.3, 6.0 & 6.2L. 2003-05, 5.3L. 6.2L without supercharger. Wire connector. 7.0L. 2008-09. Insulated to help protect the interior conductor wire Form fitting boots on each end prevent moisture from entering the coil or distributor
PCM
5.3L. Grand Prix. Corvette. SSR. 6.0L. GTO. This part requires programming and/or special setup procedures GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors Refurbishing is an industry standard practice that returns parts into service rather than scrapping them Tested to ensure they perform to GM specifications
High quality coated windings to improve durability and provide protection against internal shorts and dielectric breakdown Silicone steel plates surrounding the ignition coil correctly match the original part size and number exactly Laminations are coated to hinder corrosion and many feature molded plastic protection to help ensure that nothing is exposed
Related Parts
Air Intake Temp Sensor
This GM Genuine part is designed, engineered and tested to rigorous standards, and are backed by General Motors
Coolant Temp Sensor
Helps keep engine running at proper temperature Alerts vehicle operator of high engine temperature conditions
Crankshaft Position Sensor
Helps keep engine timing and fuel injection running in sync Helps provide proper alignment, positioning, and spacing for easy installation Synchronizes engine valves and pistons for excellent engine performance
Camshaft Position Sensor
Helps keep engine timing and fuel injection running in sync Helps provide proper alignment, positioning, and spacing for easy installation Synchronizes engine valves and pistons for excellent engine performance
Knock Sensor
Sends signals to the engine control module (ECM) to adjust timing Helps prevent damage to the engine caused by pre-ignition
Mass Air Flow Sensor
Measures the amount of air entering the engine so the ECM can determine the amount of fuel to inject This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors
This GM Genuine Part is designed, engineered, and tested to rigorous standards and is backed by General Motors